9 Steps to Install a Fire Sprinkler System in Your House

 

Though it is feasible to install a fire sprinkler system on your own, it’s advisable to consult a professional if you have any doubts regarding your efficiency in handling the plumbing and electrical aspects. You must follow the instructions from the manufacturer of your fire sprinklers systems service in California. 

 

In this article, there’s a basic outline for installing a wet system in your home. 

 

1. Confirm the Pressure on Your Water Supply 

 

If you have sufficient pressure from your city water supply, the home fire sprinkler system installation will be more convenient as the system can tie right in. A pressure of 100 PSI is perfectly okay. When you do not have enough pressure, you may have to invest in a water storage tank and pump for the sprinkler system when a fire alarm in California alerts you. 

 

2. Position Piping in the Basement 

 

Any piping is supposed to run the water from the supply in the basement across the ceiling to the sprinkler heads on the first floor. As the pipes are made of CPVC, almost identical to PVC, it's more heat resistant and will less likely melt in a fire. Join the pipes with pipe cement. You may attach pipes to the studs along with the ceiling with the help of galvanized pipe straps. 

 

3. Position Cages Around the Basement Sprinkler Heads 

 

You must install fire sprinkler heads in the basement. If you wish to prevent the sprinkler heads from accidentally being bumped and set off, then you must attach protective cages. This is particularly essential in areas where the ceiling is low. 

 

4. Make Cutouts Of First-Floor Wall  

 

To gear up the first floor for the sprinkler system, you must conceal the piping in the wall. To perform this, you must cut out sections of the drywall between the studs. 

 

5. Drill a Hole to the Basement 

 

Within the wall, drill through the bottom of the wall and the floor inside the basement underneath. Insert extra CPVC piping through the hole inside the basement so that it can be connected with the sprinkler line. Secure the piping within the wall on the first floor with the help of pipe straps. 

 

6. Run Extra Piping 

 

You'll carry on drilling and run piping as required for the installation of the piping system where the sprinklers need to sit on the first floor of the home. Apply your stud finder to confirm that you're cutting the wall open between studs. Prevent any electrical wiring. If you don't wish to cut into the ceiling of the first floor of the home, you may rather decide to mount sprinklers high up on the walls. 

 

7. Put Bedroom Sprinklers 

 

There could be second or third levels in your home that you wish to run extra piping to. The procedure is the same as with the first floor if you don’t run the piping through a closet. By applying this process, you can avoid opening up the walls on the second floor. But you must use metal piping and not CPVC if it gets exposed outside the wall. 

 

Cut a hole inside the floor of the closet so that it connects to the piping you've run on the floor beneath. It’ll help you run the piping from the second floor to the attic, where you'll route it through the ceilings of the bedrooms. Accordingly, sprinklers can be fixed in every room where someone sleeps. Position a cap on the recessed sprinkler to make it invisible. 

 

8. Insulate the Piping and Cover the Wall Cutouts 

 

When your attic is uninsulated, the piping that runs through it has to be covered in insulation to prevent the water in the pipes from freezing. Wherever you've cut out drywall, you must patch it. Piping running at the top of the wall may be covered by applying crown molding. 

 

9. Pressurize and Conduct a Leak Test 

 

Once everything is sealed and connected, the system must be pressurized and leak tested. Now, your home is ready to fight back in the event of a sudden fire. 

 

Inference 

 

The providers of your fire alarm systems in Glendora may not be readily available, but the sprinkler will be effective in this regard.